Why are my new fluorescent bulbs not working

Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. … Dimming or flickering. … No lights at all. … Changing colors. … Swollen casing. … Burn marks. … Water damage. … Leaking oil.

What are the signs of a bad ballast?

• Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. …
• Dimming or flickering. …
• No lights at all. …
• Changing colors. …
• Swollen casing. …
• Burn marks. …
• Water damage. …
• Leaking oil.

How do I know if its the ballast or bulb?

One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.

Why won't my new fluorescent lights work?

The fluorescent tube won’t turn on No electrical power due to a tripped breaker or blown fuse. A dead or dying ballast. A dead starter. A dead bulb.

How can you tell if a fluorescent light ballast is bad?

1. Flickering. …
2. Buzzing. …
3. Delayed start. …
4. Low output. …
5. Inconsistent lighting levels. …
6. Switch to an electronic ballast, keep lamp. …
7. Switch to an electronic ballast, switch to a T8 fluorescent.

Where is the ballast located on a fluorescent light?

Remove the Cover Plate Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.

Do all fluorescent lights have ballast?

All fluorescent bulbs require a ballast. All compact fluorescent (CFL) bulbs require a ballast, which is often integrated. All HID bulbs require a ballast, which is sometimes integrated. No LED bulbs require a ballast, although some are engineered to work with an existing ballast.

Where is the starter on a fluorescent light fixture?

The starter is located on the lamp frame (there are typically two starters). When you turn on the light switch, the starter sends a jolt of electricity to the gas inside the fluorescent bulb.

How do you test a fluorescent starter?

A fluorescent starter can be tested by a multimeter very easily. For this, you need to turn the power off and then attach the multimeter at the one end of the starter. This will show the reading of the electric flow in the starter. If the flow shows normal, then you have a completely working starter.

Can a fluorescent light work without a starter?

When you turn on a fluorescent tube, the starter is a closed switch. … Without the starter, a steady stream of electrons is never created between the two filaments, and the lamp flickers. Without the ballast, the arc is a short circuit between the filaments, and this short circuit contains a lot of current.

Article first time published on

How long does fluorescent ballast last?

According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.

How do I reset my HID ballast?

The ballast can only be reset by turning the headlight switch off and then on again. However, allow a few minutes cooling time between attempts to allow the ballast to cool down. If you reset have to repeatedly reset the ballast that’s often a sign of a bad HID bulb.

How much does it cost to replace a ballast?

A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.

How do I know if my ballast is T8 or T12?

If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.

Why do new fluorescent lights flicker?

The starter is responsible for the momentary delay in lighting when some fluorescent tubes are switched on. If it is faulty, it can also be the cause of initial flickering as the tube warms up, or of failure to light at all. … With these, dirt on the tube can sometimes prevent lighting or can cause flickering.

What is the difference between starter and ballast?

In older fluorescent fixtures, the ballast, or choke, is a transformer that limits the current flowing into the tube, while the starter provides the high voltage needed to excite the tube when it is turned on.

What is the difference between a ballast and a driver?

Fluorescent ballasts provide an initial spike of high voltage, generating an arc that travels from cathode to anode within the discharge tube. … LED drivers convert high voltage, ac current into the low voltage, direct current that LEDs are designed to run on.

How do I know what ballast to buy?

It needs to fit the electrical requirements of the lamp that it will run. When purchasing a ballast, you’ll need to read the type of lamps it’s designed for, how many lamps it operates, and the voltage the lamps will run on. Choosing the right ballast for a lamp will optimize the light output and life of the bulb.

Why does my fluorescent light take a long time to come on?

Most fluorescent light fixtures also have a component called a ballast, which controls the current through the fixture. If the ballast is malfunctioning, it too can cause the light to take a while to turn on. But ballasts are very expensive to replace and they malfunction far more seldom than tubes and starters.

What will happen if we remove starter after switching on the fluorescent lamp?

Tube light will not become off if you remove starter. The starter is required only at beginning to make light to glow. … The light will continue to glow.

What is a ballast starter?

The ballast initially works as a starter for the arc, supplying a high-voltage impulse and, later, it works as a limiter/regulator of the electric flow inside the circuit. Electronic ballasts also run much cooler and are lighter than their magnetic counterparts.

Do modern fluorescent tubes have starters?

Most modern fluorescent fixtures do not use starters, so you might not find one if your fixture is less than 15 to 20 years old. When determining whether your fixture uses a starter, be sure to look underneath the bulbs… sometimes the bulbs have to be removed first to gain access to the starter.

Can a bad ballast cause a fire?

As with any electrical situation where overheating is possible, a bad ballast can pose a fire danger. The overheated ballast could cause the plastic housing on the light itself to melt and, in the right conditions, flame up.

How much electricity does a ballast use?

They consume eight to 10 watts when operating with the lamp in the circuit. The ballast will consume about four watts when the lamps are removed although the ballast is still energized. Electronic ballasts start and regulate fluorescent lamps with the use of electronic components.

How do you test an HID ballast?

1. Dimming or Flickering Headlights. If your HID bulb cannot produce its full brightness or strobe periodically, this is most probably a ballast problem. …
2. Strange Sounds. …
3. Headlights Not Working. …
4. Changing Light Colors. …
5. Constantly Blowing Fuse. …
6. Damaged Casing. …
7. Burn Marks. …
8. Water or Oil Damage.

Can HID bulbs work without ballast?

Without HID ballasts, the bulbs won’t function. It is essential that you buy a HID conversion kit that includes HID bulbs, ballasts, mounting elements, wiring, etc. so that the conversion is 100% successful.

Why are my HID lights not working?

If you install your HID kit or LED kit and they do not turn on you may have a reverse polarity issue. … If your HID kit or LED kit still doesn’t light up after reversing the polarity, your headlight fuse might be too weak. Upping the fuse by 5 amps might do the trick.

Can you replace a ballast yourself?

The ballast takes in electricity and then regulates current to the bulbs. … You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.

Can you repair a ballast?

While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.

Can I put a T8 bulb in a T12 ballast?

As far as safety is concerned, you can exchange them. If you place T12 tubes in a fixture with a T8 ballast, you will wear out the ballast and have to replace it. If you place T8 tubes in a fixture with a T12 ballast, then the tubes will have a shorter life due to a higher current through the tube.

Can I put a T8 bulb in a T12 fixture?

T8 tubes are simply 1 inch in diameter versus the 1.5 inch diameter of T12 tubes. In an effort to make LED tube lights compatible with the internal dimensions of most fixtures, you will find that most LED tube lights feature a T8 or 1 inch diameter. They can indeed be used in T12 fixtures.